VERSION 1 # Currently, this should only be 1.
# Supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
TRACKNAME Roland S-1
# Can be POLY, DRUM, MPE, or NULL
TYPE POLY
# Can be A, B, C, D, USBD, USBH, CVGx (x between 1&4), CVx, Gx, or NULL
OUTPORT C
# Can be x (between 1-16), or NULL -- this is ignored if output port is not MIDI
OUTCHAN 6
# Can be NONE, ALLACTIVE, A, B, USBH, USBD, CVG, or NULL
INPORT NULL
# Can be x (between 1-16), ALL, or NULL. This definition will be ignored if INPORT is NONE, ALLACTIVE or CVG
INCHAN NULL
# This defines the default 'MAX RATE' for automation lanes.
# Can be NULL, 192, 96, 64, 48, 32, 24, 16, 12, 8, 6, 4, 3, 2, 1
MAXRATE NULL
# DRUMLANES
# Syntax: ROW:TRIG:CHAN:NOTENUMBER NAME
# ROW must be between 1 and 8
# TRIG can be between 0 and 127, or NULL
# CHAN can be a number between 1 and 16, Gx, CVx, CVGx (x between 1 and 4), or NULL
# NOTENUMBER can be between 0 and 127, or NULL
# NAME supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
# Please note this section will be discarded for tracks which are not DRUM tracks
[DRUMLANES]
[/DRUMLANES]
# PC
# Syntax: NUMBER NAME
# number must be either:
# - A number (for simple PC)
# - Three numbers, delimited by ':', which represent PC:MSB:LSB. You can put 'NULL' to not set the MSB/LSB.
# PC must be between 1...128
# MSB/LSB must be between 0...127
[PC]
[/PC]
# CC
# Syntax: CC_NUMBER NAME or CC_NUMBER:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 127
[CC]
1 Mod Whl
3 LFO RATE
5 PORT TIME
10 Pan
11 Exp
12 LFO Waveform
13 OSC LFO
14 OSC RANGE
15 OSC PULSE WIDTH
16 OSC PWM SOURCE
17 LFO MOD DEPTH
18 OSC BEND SENS
19 PULSE OSC LEVEL
20 SAW OSC LEVEL
21 SUB OSC LEVEL
22 SUB OSC TYPE
23 OSC NOISE LEVEL
24 FILT. ENV
25 FILT. LFO
26 FILT. KF
27 FILT. BEND SENS
28 AMP.ENV MODE
29 ENV. TRIGGER MODE
30 ENV. SUSTAIN
31 PORT. MODE
64 Damper Pedal
65 PORT
71 FILT. RES
72 ENV. RELEASE
73 ENV. ATTACK
74 FILT. FREQ
75 ENV. DECAY
76 FINE TUNE
77 TRANSPOSE
78 NOISE MODE
79 LFO MODE
80 POLY MODE
81 CHORD VC 2
82 CHORD VC 3
83 CHORD VC 4
85 CHORD VC 2 KEY
86 CHORD VC 3 KEY
87 CHORD VC 4 KEY
89 REVERB TIME
90 DELAY TIME
91 REVERB LEVEL
92 DELAY LEVEL
93 CHORUS
102 OSC DRAW MULT
103 OSC CHOP OVERTONE
104 OSC CHOP COMB
105 LFO KEY TRIGGER
106 LFO SYNC
107 OSC DRAW SW
[/CC]
# NRPN
# Syntax: "MSB:LSB:DEPTH NAME" or "MSB:LSB:DEPTH:DEFAULT=xx NAME"
# Lsb & msb should be between 0 and 127
# Note: LSB can be over 127 ONLY if MSB is 0 or omitted
# e.g. '0:1026:7 FOO', or ':2000:7 BAR'
# the examples above would be equivalent to '8:2:7 FOO' and '15:80:7 BAR' respectively
# DEPTH can be 7 or 14
# For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
[NRPN]
[/NRPN]
# ASSIGN
# Syntax: POT_NUMBER TYPE:VALUE or POT_NUMBER TYPE:VALUE DEFAULT=DEFAULT_VALUE
# POT_NUMBER must be between 1 and 8
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", "NRPN", or "NULL" (this won't assign the pot).
# Non explicitly-defined pots will be considered "NULL"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# DEFAULT VALUE
#### For CC: DEFAULT_VALUE must be a valid number between 0 and 127
#### For PB: DEFAULT_VALUE must be a valid number between 0 and 16383
#### For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
#### For CV: DEFAULT_VALUE must be either a valid number between 0 and 65535, or a voltage between -5V and 5V, e.g. "-4.25V" or "1.7V"
#### Please note default value will be ignored for PB and AT messages.
[ASSIGN]
[/ASSIGN]
# AUTOMATION
# Syntax: TYPE:VALUE
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", or "NRPN"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# NOTE: You are limited to 64 automation lanes
[AUTOMATION]
[/AUTOMATION]
# This section will be readable from Hapax.
[COMMENT]
Roland S-1
[/COMMENT]
Midi Implementation for the Roland S1, lifted from the v1.02 manual. Actually unlocks a load of other features that aren’t easily accessible. Leave the S1 with an empty sequence and then you can automate and sequence it directly from the Hapax 