VERSION 1 # Currently, this should only be 1.
# Supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
TRACKNAME Tooro
# Can be POLY, DRUM, MPE, or NULL
TYPE NULL
# Can be A, B, C, D, USBD, USBH, CVGx (x between 1&4), CVx, Gx, or NULL
OUTPORT NULL
# Can be x (between 1-16), or NULL -- this is ignored if output port is not MIDI
OUTCHAN NULL
# Can be NONE, ALLACTIVE, A, B, USBH, USBD, CVG, or NULL
INPORT NULL
# Can be x (between 1-16), ALL, or NULL. This definition will be ignored if INPORT is NONE, ALLACTIVE or CVG
INCHAN NULL
# This defines the default 'MAX RATE' for automation lanes.
# Can be NULL, 192, 96, 64, 48, 32, 24, 16, 12, 8, 6, 4, 3, 2, 1
MAXRATE NULL
# DRUMLANES
# Syntax: ROW:TRIG:CHAN:NOTENUMBER NAME
# ROW must be between 1 and 8
# TRIG can be between 0 and 127, or NULL
# CHAN can be a number between 1 and 16, Gx, CVx, CVGx (x between 1 and 4), or NULL
# NOTENUMBER can be between 0 and 127, or NULL
# NAME supports all alphanumeric ASCII, and ' ', '_', '-', '+' - can also be NULL
# Please note this section will be discarded for tracks which are not DRUM tracks
[DRUMLANES]
[/DRUMLANES]
# PC
# Syntax: NUMBER NAME
# number must be either:
# - A number (for simple PC)
# - Three numbers, delimited by ':', which represent PC:MSB:LSB. You can put 'NULL' to not set the MSB/LSB.
# PC must be between 1...128
# MSB/LSB must be between 0...127
[PC]
[/PC]
# CC
# Syntax: CC_NUMBER NAME or CC_NUMBER:DEFAULT=xx NAME
# DEFAULT_VALUE must be a valid number between 0 and 127
[CC]
1 Modwheel
70 Osc 1 Wave
21 Osc 1 Coarse
22 Osc 1 FM Amount
23 Osc 1 Level
24 Osc 1 Table
25 Osc 1 Fine
26 Osc 1 FM Rate
27 Osc 1 Sync
77 Osc 2 Wave
31 Osc 2 Coarse
32 Osc 2 FM Amount
33 Osc 2 Level
34 Osc 2 Table
35 Osc 2 Fine
36 Osc 2 FM Rate
37 Osc 2 Sync
78 Extra Noise
79 Extra Ring
73 AmpEnv Attack
40 AmpEnv Decay
41 AmpEnv Sustain
72 AmpEnv Release
43 AmpEnv Velo
42 AmpEnv Hold
44 AmpEnv After
45 AmpEnv Trigger
46 FltEnv Attack
47 FltEnv Decay
48 FltEnv Sustain
49 FltEnv Release
51 FltEnv Velo
50 FltEnv Hold
52 FltEnv After
53 FltEnv Trigger
71 Filter Resonance
74 Filter Cutoff
54 Filter Env F Amount
55 Filter Track
56 Filter After
57 Filter LFO 1 Amount
75 Shaper Cutoff
76 Shaper Resonance
58 Shaper Env A Amount
59 Shaper Track
60 Shaper Mode
61 Shaper LFO 2 Amount
102 LFO 1 Shape
103 LFO 1 Speed
104 LFO 2 Rise
105 LFO 1 Phase
106 LFO 2 Shape
107 LFO 2 Speed
108 LFO 2 Rise
109 LFO 2 Phase
110 Arp Mode
111 Arp Grid
112 Arp Tempo
113 Arp Hold
80 Amp Level
81 Amp Pan
17 Modulation Env F
18 Modulation Env A
19 Modulation LFO 1
20 Modulation LFO 2
87 Modulation Mod Wheel
88 Modulation Pitch
89 Modulation Velocity
90 Modulation Aftertouch
86 Bend Range
85 Tune
07 Multi Level
10 Mutli Balance
91 FX Mix
12 FX Feedback
14 FX Length
93 FX Depth
13 FX Mode
15 FX Speed
120 All Sounds Off
121 Reset All Controllers
123 All Notes Off
124 Omni Off
125 Omni On
126 Mono Mode
127 Poly Mode
[/CC]
# NRPN
# Syntax: "MSB:LSB:DEPTH NAME" or "MSB:LSB:DEPTH:DEFAULT=xx NAME"
# Lsb & msb should be between 0 and 127
# Note: LSB can be over 127 ONLY if MSB is 0 or omitted
# e.g. '0:1026:7 FOO', or ':2000:7 BAR'
# the examples above would be equivalent to '8:2:7 FOO' and '15:80:7 BAR' respectively
# DEPTH can be 7 or 14
# For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
[NRPN]
[/NRPN]
# ASSIGN
# Syntax: POT_NUMBER TYPE:VALUE or POT_NUMBER TYPE:VALUE DEFAULT=DEFAULT_VALUE
# POT_NUMBER must be between 1 and 8
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", "NRPN", or "NULL" (this won't assign the pot).
# Non explicitly-defined pots will be considered "NULL"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# DEFAULT VALUE
#### For CC: DEFAULT_VALUE must be a valid number between 0 and 127
#### For PB: DEFAULT_VALUE must be a valid number between 0 and 16383
#### For NRPN: DEFAULT_VALUE must be a valid number, either between 0 and 127 (for 7 bit NRPNs) or between 0 and 16383 (for 14bit NRPNs)
#### For CV: DEFAULT_VALUE must be either a valid number between 0 and 65535, or a voltage between -5V and 5V, e.g. "-4.25V" or "1.7V"
#### Please note default value will be ignored for PB and AT messages.
[ASSIGN]
[/ASSIGN]
# AUTOMATION
# Syntax: TYPE:VALUE
# TYPE can be "CC", "PB" (pitchbend), "AT" (aftertouch), "CV", or "NRPN"
# VALUE VALIDATION
#### For CC: Value must be a valid number between 0 and 119
#### For PB and AT, any text after the TYPE will be ignored
#### For CV, value must be between 1 and 4
#### For NRPN, value must be MSB:LSB:DEPTH, with both lsb & msb bebtween 0 and 127, and DEPTH being either 7 or 14
# NOTE: You are limited to 64 automation lanes
[AUTOMATION]
[/AUTOMATION]
# This section will be readable from Hapax.
[COMMENT]
[/COMMENT]
Comments about your instrument definition goes here